You need to fine tune the spray nozzle by turning the adjustment nozzle all the way to the negative side (-). Then while holding the trigger down, slowly adjust the nozzle toward the positive side (+) until you get a nice even spray. You should also make sure that the pen is fully inserted by pushing it all the way into the slot on the spray gun until you hear/feel it click.
|
You can, but the adhesive should be applied to a clean, smooth, dry surface when the temperature is above 50°F (10°C). If the temperature is below 50°F, you can heat the surface with a hair dryer before application.
|
After the figures are connected, cranked up and the head is pushed, the “wrestling” feature does not last long.
- Crank the lever clockwise until it clicks, usually about 11 times, for full power battling.
|
To clean the ink off of your car, rub it with a damp cloth and start again!
|
Push the handle on the far right counterclockwise all the way to the ground and the car platform will tip forward, allowing your car to roll out.
|
The booster needs to be correctly assembled to its designated wall bracket in order to function. The designated wall bracket has a notch on it. This notch ensures the motor only works when attached to the bracket. All other brackets are flat.
Watch set-up instructions for your track.
|
Click here for instructions on how to clear app data on your tablet.
|
-
You can customize your vehicle in the workshop. Follow the green tool icon to find the workshop hangar.
-
There are multiple types of customizations that you can make:
-
One-shots are one-time game modifiers that you can use to improve your performance, such as nitro bursts that give you faster speed. However, after you use a one-shot, you no longer have it anymore. You would need to unlock another one to use it again.
-
Add-ons are customizations that can be used forever on your vehicle, such as tires or weapons. Once you have unlocked them, they are permanently available for your use.
-
In order to modify your vehicle in the workshop, tap any icon in the circle with your finger and it will take you to the page where you can unlock it, if you have enough credits.
-
You can purchase more credits to unlock specific one-shot or add-on modifications. Once add-ons are purchased, they will always be available to equip your car.
|
Hot Wheels replacement parts are available at our
Parts Store.
|
-
If you hear “Error,” ask an adult to unplug Car Maker from the wall, wait ten seconds and then plug it back in to reset. Car Maker may automatically go into the cooling cycle. Do not unplug during this time. If you continue to hear “Error” after multiple resets, this may be an indication of a mechanical problem with the door switch; please contact Consumer Services via service.mattel.com for assistance.
|
The more you play the game, the more credits you earn. You can redeem credits in the workshop. Your credits are listed in the top right corner of the screen.
|
- Change batteries
- Check for obstructions around moving parts
|
|
First insert the flexible stencils into the frame with the built-in peg fitting. Connect the frame onto the four posts on top of the car decoration turntable, and then adjust the height of the frame for tall and low cars by using the two detent locations. Remember that in order to spray using stencil, the airbrush must face directly down over the top of the car and spray through the stencil.
|
There is a silver-colored speed control button on the lower left side of the screen. The image on it is a gear box. Tap the button to move from “Stop” mode to “Slow” and “Fast” modes.
|
Make sure the pen is fully inserted by pushing it all the way into the slot on the spray gun until you hear/feel it click. Start spraying with the nozzle adjuster pointed all the way toward the negative side (-) and, while holding the trigger down, slowly move the adjuster toward the positive side (+) until you get a nice even spray. If you’re still having issues, please refer to the troubleshooting section below.
|
There are many reasons that variations exist on the same Hot Wheels car model. For instance, changes may occur in mid-production as a result of a licensing issue or a manufacturing change.
|
The WWE Power Slammers Ring is supposed to get scuffed up after the figures wrestle, on purpose, to show “battle damage”.
|
To cover existing paint or color you will need to apply multiple coats. First paint a thin, light coat and let it dry. Then repeat the process until you get the paint coverage you want.
|
When the WWE Power Slammers figures are connected, cranked up and the head is pushed to start, they start to move, but then get caught or don’t move.
-
For the Thunder Twisting figures, John Cena, Zack Ryder and Sheamus, make sure the arm is straight before you push the head to start the wrestling. If the arm is bent it causes the figures to get caught and not wrestle.
|