|
You will need a powered USB port from a computer, laptop or USB charger.
|
|
2.4 GHz.
|
|
To fully charge, the hoverboard should be to be plugged in for about 90 to 120 minutes. To charge, please reference instruction sheets or demo video on YouTube.
|
|
Yes; maximum of 6 at the same time.
|
|
Turn on hoverboard and place it on a flat surface, and then controller to the ON position. Wait for the beep. Once the green light is on, the controller will stop flashing and the devices are paired.
|
|
No. Barbie is attached to the hoverboard.
|
|
Turn off both devices and repeat pairing steps. Reference the instruction sheets provided in the package.
|
|
No. Please reach out to Mattel Consumer Services for replacement propellers.
|
|
The remote should last for hours of play if it is turned off properly after play each time.
|
|
To activate your Barbie® RC Train and Ride™ Horse, Press and hold the button on its forehead until the horse takes a step. Press the button again to make the horse walk. If the horse is not played with for a few minutes, it will go into a sleep mode. Simply press and hold the button on the horse’s forehead until it takes a step to wake it up.
|
No. Mattel meets or exceeds all safety guidelines developed and enforced by the Consumer Product Safety Commission, a government regulatory agency. For additional information on safety and sustainability, consumers can go to our website http://citizenship.mattel.com and then click on Safe and Sustainable Products.
|
|
The joystick directions match the direction that Barbie is facing, rather than the direction that the operator is facing. If Barbie is facing away from you and you move the joystick forward, Barbie will fly away from you. If she is facing towards you and you move the joystick forward, she will move towards you.
|
|
Fully charged, the Barbie™ Star Light Adventure RC Hoverboard will fly for about 7 minutes.
|
|
Match the color of propellers to the motor container. Keep the propellers perpendicular to the motor pins. Gently press propellers in until they stop.
|
The Imaginext® DC Super Friends™ RC Transforming Bat Bot’s remote is shipped without batteries, so please be sure to place two AAA batteries into the remote. Also, there is a clear plastic packaging tab that is attached to the outer leg of the non-battery leg of the robot. The tab should come out of the leg when removed from the box; however, it’s possible that a piece of the plastic remained in the slot on the leg. Please check the slot, which is located behind the front wheel. If you see clear plastic protruding from the slot, carefully remove it with tweezers, and turn the toy off and on again. This should clear the slot and make the toy function as it normally should.
|
|
If Barbie™ Star Light Adventure RC Hoverboard keeps moving after launching, use the Trim buttons, located around the joystick to adjust. Press Trim button in opposite direction where Barbie™ Star Light Adventure RC Hoverboard moves until it remains still in the air. Press once and wait a few seconds until it is stabilized.
|
|
Connect the controller to a powered USB port with the supplied USB cable. Attach the power cable located inside the controller to Barbie™ Star Light Adventure RC Hoverboard. Set the toy to OFF position and controller in “charging” position (left). Charging light should be in red and turns green when it is fully charged.
|
|
The Barbie™ Star Light Adventure RC Hoverboard will fly about 5 meters or 17 feet from the surface it launches from.
|
|
The Barbie™ Star Light Adventure RC Hoverboard is meant for indoor use. The toy may not work properly when used outdoors and will be affected by wind and/or heat.
|
You will need to perform a factory reset of the Batmobile RC vehicle. **The Batmobile needs to be on all four wheels to do the reset.** The battery compartment is located on the left side of the vehicle. Remove the battery door and locate the small hole on the bottom left hand corner of the battery housing. While the Batmobile vehicle is turned ON, insert and press down the reset button located in the recessed area for 10 full seconds using a paperclip or similar sized tool. After holding down for 10 full seconds, release the button, wait 3 seconds and then cycle the Batmobile OFF and then back ON, and follow the "new user" instructions to connect to the Batmobile in the Batmobile RC Controller app.
|
