After you’ve airbrushed your car, lower the turntable into the drying chamber by turning the handle on the far right counterclockwise toward the ground. Rotate the knob outside the chamber all the way to the rightmost setting to turn the fan on. Air will blow inside the drying chamber and dry off your car!
|
|
Click here to see the instructions on how to perform a hard factory reset on your tablet.
|
The action button is the button on the hood of the car that you can press down in order to start the game, activate weapons, enter buildings and other zones, and more.
|
In order for the Wild Thing™ to operate correctly, there must be weight in the seat. When your child leans forward in the seat or lifts their bottom off the seat, the seat switch will open and the vehicle will stop. For best results, make sure your little one stays seated at all times with their back against the seat.
|
Since 1968, when Hot Wheels cars were introduced, we have manufactured tracks in many different colors, yet the color that sticks in the minds of most people is orange. As in the past, we will continue to manufacture tracks in many different colors that will vary from set to set, and year to year.
|
|
Click on the map icon in top left corner of screen. You can click on any of the icons to be taken to that particular area of the Test Facility.
|
The tutorial only plays once, but parts of it can be viewed again by clicking on the map icon on the top left corner of your screen.
|
-
The very first time you use Car Maker, you need to insert 2 wax sticks. Car Maker comes pre-loaded with 1 wax stick. The second stick you insert is not meant to fit completely inside the machine – it will protrude through the top. After you have made your very first car, only 1 additional wax stick needs to be inserted every time. Please note that ALL wax sticks must be inserted with the point side down.
|
You can combine your pens to get more color combinations. For example, you can get green by applying blue and yellow inks over each other. First apply a thin layer of one color until you get the desired coverage, then switch pens and apply an even layer of your second ink. Try making your own combinations!
|
On
the underside of the launcher, each end of the rubber band should be wrapped
around a peg on each side of the main launcher and then doubled up and hooked
around the center tab of the moveable portion of the launcher.
Here is a picture of an assembled rubber band launcher!
|
-
First, ensure that the car is specifically meant for the Apptivity Hot Wheels game, and not a regular Hot Wheels car. You will be able to tell whether it is for Apptivity by looking for the contact points on the bottom of the car.
-
Ensure that the contact points are extended rather than retracted. There is a button on the bottom of the car that allows you to switch between traditional Hot Wheels car play (retracted) and Apptivity mode (extended).
-
Check the bottom of the car for debris, and wipe it with a clean, dry cloth.
-
Wipe your screen with a soft, dry cloth to ensure the best conductivity with the car.
-
Make sure you are holding the car in the right location in order for it to be recognized.
-
Hold it in the center and on the sides of the car while the tires are on the screen.
-
Make sure that you are not placing the car on the black or white frame around the iPad screen. You must keep the car only within the screen area.
-
Do not wear gloves or mittens since the car needs to come in contact with your fingertips.
|
You need to fine tune the spray nozzle by turning the adjustment nozzle all the way to the negative side (-). Then while holding the trigger down, slowly adjust the nozzle toward the positive side (+) until you get a nice even spray. You should also make sure that the pen is fully inserted by pushing it all the way into the slot on the spray gun until you hear/feel it click.
|
You can, but the adhesive should be applied to a clean, smooth, dry surface when the temperature is above 50°F (10°C). If the temperature is below 50°F, you can heat the surface with a hair dryer before application.
|
Variations in Hot Wheels cars are the slight differences between cars of the same model. For example, with the many different wheel styles available, the same car model can have a wildly different look just by changing the wheels.
|
After the figures are connected, cranked up and the head is pushed, the “wrestling” feature does not last long.
- Crank the lever clockwise until it clicks, usually about 11 times, for full power battling.
|
To clean the ink off of your car, rub it with a damp cloth and start again!
|
The WWE Power Slammers figures are difficult to connect at the arms the first couple of times. Each time you connect the figures, it will become easier and easier to connect.
The new figures released in the Fall 2013 will be easier to connect.
|
Push the handle on the far right counterclockwise all the way to the ground and the car platform will tip forward, allowing your car to roll out.
|