First insert the flexible stencils into the frame with the built-in peg fitting. Connect the frame onto the four posts on top of the car decoration turntable, and then adjust the height of the frame for tall and low cars by using the two detent locations. Remember that in order to spray using stencil, the airbrush must face directly down over the top of the car and spray through the stencil.
|
- If you have inserted different colored wax sticks next to each other, you may get some color blending (in which the wax from the two adjacent sticks mix when creating the car body).
|
You should place the Apptivity Hot Wheels car on the screen in that location in order to play.
|
-
Once Car Maker instructs you to pull the handle, you must immediately pull it all the way down in one continuous motion until you hear “Complete.” For best results, DO NOT pump handle when pulling it down and complete the injection within 2-3 seconds. If you do not pull it all the way down to complete the injection, Car Maker will keep repeating the phrase, “Please pull down handle.”
|
There is a silver-colored speed control button on the lower left side of the screen. The image on it is a gear box. Tap the button to move from “Stop” mode to “Slow” and “Fast” modes.
|
-
From your iPad home screen, go to Settings, General, then Multitasking Gestures. Turn off Multitasking Gestures.
-
Make sure that you do not press the car down on the iPad home button, as that will close the game.
|
Make sure the pen is fully inserted by pushing it all the way into the slot on the spray gun until you hear/feel it click. Start spraying with the nozzle adjuster pointed all the way toward the negative side (-) and, while holding the trigger down, slowly move the adjuster toward the positive side (+) until you get a nice even spray. If you’re still having issues, please refer to the troubleshooting section below.
|
Use the circular stencil tool to add detail to your artwork. First fully insert the pen until you hear/feel it click and adjust the spray nozzle until you get a nice even spray. Then plug the circular stencil tool directly onto the end of the airbrush tip. Rotate the stencil to select the artwork that you would like to apply. The art should be centered over the spray tip and applied to the car in close range.
|
|
You should pull the car back so that your car stays in that location on the screen.
|
There are many reasons that variations exist on the same Hot Wheels car model. For instance, changes may occur in mid-production as a result of a licensing issue or a manufacturing change.
|
The WWE Power Slammers Ring is supposed to get scuffed up after the figures wrestle, on purpose, to show “battle damage”.
|
-
If you cannot press the handle down, have an adult unplug the machine, wait ten seconds and then plug it back in to reset. Car Maker will automatically go into the cooling cycle. Do not unplug during this time. After you hear “Cooling Complete” and the door opens, try the following:
-
Check the mold for blockage. See CLEANING section in the instruction sheet.
-
Look into the front window on the machine. Ensure that there is a wax stick in the heating chamber and that the wax stick above it is properly aligned.
|
The various colored icons are meant to direct you to the different hangars in the Hot Wheels Test Facility. The red diamond icon takes you to the Search and Destroy Hangar, the yellow triangle icon takes you to the Long Jump Hangar, and the blue circle icon takes you to the Race Hangar. The green tool icon will allow you to upgrade your vehicle in the workshop.
|
You need the appropriate piece of equipment, such as a flotation device, big-wheel tires or wings, to access certain areas. You can get this equipment in the Workshop, which you can find by following the green tool icon, then pressing the action button once you arrive at the Workshop hangar.
|
To cover existing paint or color you will need to apply multiple coats. First paint a thin, light coat and let it dry. Then repeat the process until you get the paint coverage you want.
|
You should hear/feel it click when you push the pen down into its slot on the spray gun.
|
Mattel does not sell Treasure Hunt cars directly to consumers. All of these vehicles are limited in quantity and subject to availability.
|
When the WWE Power Slammers figures are connected, cranked up and the head is pushed to start, they start to move, but then get caught or don’t move.
-
For the Thunder Twisting figures, John Cena, Zack Ryder and Sheamus, make sure the arm is straight before you push the head to start the wrestling. If the arm is bent it causes the figures to get caught and not wrestle.
|
You need to fine tune the spray nozzle by turning the adjustment nozzle all the way to the negative side (-). Then while holding the trigger down, slowly adjust the nozzle toward the positive side (+) until you get a nice even spray. You should also make sure that the pen is fully inserted by pushing it all the way into the slot on the spray gun until you hear/feel it click.
|