You should pull the car back so that your car stays in that location on the screen.
|
There are many reasons that variations exist on the same Hot Wheels car model. For instance, changes may occur in mid-production as a result of a licensing issue or a manufacturing change.
|
-
If you cannot press the handle down, have an adult unplug the machine, wait ten seconds and then plug it back in to reset. Car Maker will automatically go into the cooling cycle. Do not unplug during this time. After you hear “Cooling Complete” and the door opens, try the following:
-
Check the mold for blockage. See CLEANING section in the instruction sheet.
-
Look into the front window on the machine. Ensure that there is a wax stick in the heating chamber and that the wax stick above it is properly aligned.
|
The various colored icons are meant to direct you to the different hangars in the Hot Wheels Test Facility. The red diamond icon takes you to the Search and Destroy Hangar, the yellow triangle icon takes you to the Long Jump Hangar, and the blue circle icon takes you to the Race Hangar. The green tool icon will allow you to upgrade your vehicle in the workshop.
|
You need the appropriate piece of equipment, such as a flotation device, big-wheel tires or wings, to access certain areas. You can get this equipment in the Workshop, which you can find by following the green tool icon, then pressing the action button once you arrive at the Workshop hangar.
|
To cover existing paint or color you will need to apply multiple coats. First paint a thin, light coat and let it dry. Then repeat the process until you get the paint coverage you want.
|
You should hear/feel it click when you push the pen down into its slot on the spray gun.
|
Mattel does not sell Treasure Hunt cars directly to consumers. All of these vehicles are limited in quantity and subject to availability.
|
You need to fine tune the spray nozzle by turning the adjustment nozzle all the way to the negative side (-). Then while holding the trigger down, slowly adjust the nozzle toward the positive side (+) until you get a nice even spray. You should also make sure that the pen is fully inserted by pushing it all the way into the slot on the spray gun until you hear/feel it click.
|
After you’ve airbrushed your car, lower the turntable into the drying chamber by turning the handle on the far right counterclockwise toward the ground. Rotate the knob outside the chamber all the way to the rightmost setting to turn the fan on. Air will blow inside the drying chamber and dry off your car!
|
|
Click here to see the instructions on how to perform a hard factory reset on your tablet.
|
The Power Wheels® 12V Quick Charger will not produce an output until it is plugged into a working Power Wheels® battery. The charger needs to detect a battery before it starts charging, so no voltage will be present when testing it with a volt meter.
|
The action button is the button on the hood of the car that you can press down in order to start the game, activate weapons, enter buildings and other zones, and more.
|
Since 1968, when Hot Wheels cars were introduced, we have manufactured tracks in many different colors, yet the color that sticks in the minds of most people is orange. As in the past, we will continue to manufacture tracks in many different colors that will vary from set to set, and year to year.
|
We have a network of over 350 Authorized Service Centers to help you with repairs and replacement parts. These Service Centers have skilled personnel and use only genuine Power Wheels replacement parts to fix your vehicle. Use our Service Center Locator to find a service center near you.
|
|
Click on the map icon in top left corner of screen. You can click on any of the icons to be taken to that particular area of the Test Facility.
|
The tutorial only plays once, but parts of it can be viewed again by clicking on the map icon on the top left corner of your screen.
|
-
The very first time you use Car Maker, you need to insert 2 wax sticks. Car Maker comes pre-loaded with 1 wax stick. The second stick you insert is not meant to fit completely inside the machine – it will protrude through the top. After you have made your very first car, only 1 additional wax stick needs to be inserted every time. Please note that ALL wax sticks must be inserted with the point side down.
|