When the WWE Power Slammers figures are connected, cranked up and the head is pushed to start, they start to move, but then get caught or don’t move.
-
For the Thunder Twisting figures, John Cena, Zack Ryder and Sheamus, make sure the arm is straight before you push the head to start the wrestling. If the arm is bent it causes the figures to get caught and not wrestle.
|
After the figures are connected, cranked up and the head is pushed, the “wrestling” feature does not last long.
- Crank the lever clockwise until it clicks, usually about 11 times, for full power battling.
|
The WWE Power Slammers figures are difficult to connect at the arms the first couple of times. Each time you connect the figures, it will become easier and easier to connect.
The new figures released in the Fall 2013 will be easier to connect.
|
The WWE Power Slammers Ring is supposed to get scuffed up after the figures wrestle, on purpose, to show “battle damage”.
|
Due to the technical nature of Power Wheels® products, some Power Wheels® parts may only be installed by our authorized service centers, therefore we’re unable to provide repair manuals or diagrams. Power Wheels® has independently owned and operated authorized service centers that carry replacement parts, batteries, and chargers in addition to repairing vehicles in or out of warranty. Our Service Center locator will assist you in finding one of our authorized service centers in your area as well as provide you website addresses for service centers that offer on-line shopping.
|
- Change batteries
- Check for obstructions around moving parts
|
For any issue with the Power Wheels® 12V Quick Charger please follow this Flow Chart.
|
We have a network of over 350 Authorized Service Centers to help you with repairs and replacement parts. These Service Centers have skilled personnel and use only genuine Power Wheels replacement parts to fix your vehicle. Use our Service Center Locator to find a service center near you.
|
Do not place used batteries in your regular trash. Instead, return the battery to a federal or state approved lead-acid battery recycler. This may be a Power Wheels® Authorized Service Center or a local retailer of automotive batteries.
|
Traction bands have been designed for and are included for use on specific single seat Jeep models to improve traction. The unauthorized use of traction bands on other Power Wheels® vehicles will void the product warranty and may pose both safety and reliability issues including decreased motor and/or gearbox life.
|
The Power Wheels® 12V Quick Charger will not produce an output until it is plugged into a working Power Wheels® battery. The charger needs to detect a battery before it starts charging, so no voltage will be present when testing it with a volt meter.
|
Battery life will vary depending on how you follow the Charging and Battery Care Instructions. It's also affected by the total number of hours the batteries are used. Average battery life is one to three years.
|
In order for the Wild Thing™ to operate correctly, there must be weight in the seat. When your child leans forward in the seat or lifts their bottom off the seat, the seat switch will open and the vehicle will stop. For best results, make sure your little one stays seated at all times with their back against the seat.
|
Make sure you charge the battery for at least 18 hours (30 hours max) before operating your vehicle for the first time. Charge the battery for at least 14 hours after each use of the vehicle. *It is necessary to charge the battery immediately after use. It is damaging to the battery when it has been used and then sits without being charged. After a full charge the battery can sit up to two-three months when not in use.
|
We have a network of over 350 Authorized Service Centers to help you with repairs and replacement parts. These Service Centers have skilled personnel and use only genuine Power Wheels replacement parts to fix your vehicle. Use our Service Center Locator to find a service center near you.
|
Connect the controller to a powered USB port with the supplied USB cable. Attach the power cable located inside the controller to Barbie™ Star Light Adventure RC Hoverboard. Set the toy to OFF position and controller in “charging” position (left). Charging light should be in red and turns green when it is fully charged.
|
|
If this occurs during the Hello Barbie™ setup process, make sure the doll is properly charged. Hello Barbie™ should remain in the charging station and connected to power during the setup.
When putting Hello Barbie™ into connection mode, make sure you see white flashing lights (they may also look light blue) If the lights flash (royal) blue, Hello Barbie™ has been reset and will automatically say "My batteries need to recharge. Please connect me to the charging station." Connect Hello Barbie™ to the charger and continue putting her into connection mode.
If this occurs during conversations or red lights appear, connect Hello Barbie™ to her charger, make sure that the charging cable is firmly connected to the doll, and that the orange charging indicator is illuminated.
|
A. We recommend using alkaline batteries with our products, as they are great for long-term use and help optimize performance. We don't recommend using Carbon-Zinc batteries. While Carbon-Zinc batteries may work well with low-power devices, they can drain after a short period of time and cause certain products to not function properly.
|
We recommend using alkaline batteries with our products, as they are great for long-term use and help optimize performance. We don't recommend using Carbon-Zinc batteries. While Carbon-Zinc batteries may work well with low-power devices, they can drain after a short period of time and cause certain products to not function properly.
|