-
PC: Windows Vista, Windows 7, Windows 8, Windows 8.1, Intel® Core™ i3 Processor, 2 GB RAM
|
No, Windows and Mac computers are supported only through USB. Please connect Monster Maker to your computer with a standard A-to-B USB printer cable (not included).
|
For best results, make sure doll parts are clean and dry before installing in Monster Maker. If your design did not print completely, erase ink using the provided sponge. Add water and a little dish soap (not included) and rub with the sponge until the ink is removed. Dry the doll part thoroughly before putting it back in the Monster Maker.
|
In the drawer, on the right side of the printer.
|
|
|
|
Next to the On/Off switch, behind the rubber plug.
|
Touch the screen with your finger or push the action button to move forward.
If the game keeps freezing, try doing a hard reset. Click the home button on your iPad to get to the home screen. Then double-click the home button again. The multitasking bar will appear. Touch the thumbnail of the Apptivity game until it wiggles, and then touch the minus button. Then click the home button again, and restart the game by clicking the thumbnail for the game on your home screen.
|
Always remove the marker from the Monster Maker when printing is complete. Replace cap on marker immediately after use. Store the markers in the tool stand, cap side down, when not in use. If left uncapped, markers will dry out. Markers can be partially restored by replacing the caps and storing them in the tool stand, cap side down, for 24 hours. Use the included markers only with the Monster Maker.
|
The app may display this message if the doll part is not installed completely. Make sure that the doll part is installed per the instructions, and that the carriage slide is lined up with the doll part icon.
|
From your iPad home screen, go to Settings, General, then Multitasking Gestures. Turn off Multitasking Gestures.
Make sure that you do not press the figure down on the iPad home button, as that will close the game.
|
|
If you receive an error message during printing, turn off the Monster Maker using the power switch. Wait a few seconds and turn it back on. Restart the app.
|
If you want to come back to play later, simply lift up your fingers or the figure to get the pause menu. Then press the iPad home button to minimize the app.
You cannot go to the main menu to switch between characters without losing your progress.
|
|
Additional red, purple, and black markers are available in the Monster Maker Primary Extension Pack, sold separately.
|
· The action button is the button on the top of the figure’s base that you can press down in order to advance dialogue, use your character’s special ability in the game, and interact with your environment.
|
No, unless you are playing with your fingers. Each figure can only be used in that specific character’s game.
|
Items that can be collected or interacted with have a glow around them. To collect an object, move the figure near the object or over it.
|
-
Monster Maker is made for iPad Air, iPad mini with Retina display, iPad (4th generation), iPad mini, and iPad (3rd generation). iOS 7.0 or higher is required.
-
Monster Maker is compatible with Samsung Galaxy Tab®, Samsung Galaxy Tab® 2, Samsung Galaxy Tab® 3, Samsung Galaxy Tab®, 8.9, Samsung Galaxy Tab® 10.1, Samsung Galaxy Note®, Google Nexus 7 (2012), Google Nexus 7 (2013), Google Nexus 10, Sony Xperia™ Tablet Z, Toshiba Excite™.
|
Please go to
service.mattel.com
to request replacement parts . Please store the adapters in the tool stand when not in use.
|
Check the bottom of the base for debris, and wipe it with a clean, dry cloth.
Wipe your screen with a soft, dry cloth to ensure the best conductivity with the figure.
Make sure you are holding the figure in the right location in order for it to be recognized. Hold it on the sides of the base where the black indented finger grips are. Do not wear gloves or mittens since the base needs to come in contact with your fingertips.
Make sure that you are not placing the figure on the black or white frame around the iPad screen. You must keep the figure only within the screen area.
|
|
|
