1. Make sure the InteracTV controller has good batteries. Slide the 3 position memory switch, on the back of the controller, to the desired memory position. The controller is capable of being setup for up to 3 different DVD players in 3 different locations.The controller must be setup and tested individually for each of the 3 DVD players, but once that is done the controller will retain the manufacturer's code and does not need to be setup again.If the consumer accidentally enters a new valid 4-digit manufacturer’s code, then they must set it up again for that DVD player.It is a good idea to write the 4-digit manufacturer’s code in the labeling area provided on the back of the controller.
2. Insert the compilation DVD into the DVD player and turn on the DVD player and TV.
3. Insert the programming card into the controller; the green light should blink twice.
4. Locate the manufacturer’s codes in the user’s manual.
5. Enter the first 4 digit code listed under the manufacturer. Use the right arrow button for the number. The light should blink after each button press and blink a long blink after the 4^th digit is entered.
6. Remove the programming card.The light should double blink when the card is removed
7. Insert the test card into the unit;the green light should double blink.
8. The DVD should skip to the test screen, if it does not, repeat from step 3, choosing the next manufacturer’s code on the list. If the test card skips to the footage, which resembles the test card, then proceed with testing the unit.See Testing the unit section of you manual or quick setup instructions.
9. If you have tried all of the manufacturer's codes listed and you cannot locate an acceptable code, see programming the unit using manual search in your user's manual.

• Make sure you have set up your InteracTV controller correctly.
• Try moving your InteracTV controller closer to the TV.
• Replace the batteries on your InteracTV controller.
• Make sure your InteracTV controller is pointed directly at your DVD player.
• Always be sure your hand and the activity card are not covering the red window on the front of the InteracTV controller when removing and inserting an activity card.
• Make sure there are no large objects between your InteracTV controller and your DVD player. Large objects can block the signal between your controller and DVD player.
• When changing activity cards, always make sure you remove the activity card from your InteracTV controller slowly, wait a few seconds, and then insert another activity card.
• Double check that the 3-position memory switch on the underside of your InteracTV controller is in the proper position. Refer to your InteracTV User's Manual for instructions on how touse the 3-position memory switch.

InteracTV™ is a mark of Beep Telecommunications and Computing, L.L.C. Used under license.

You only need to set up your InteracTV controller one time per DVD player. Your InteracTV controller can be set up to be played with up to three different DVD players. There is a 3-position memory switch on the underside of your InteracTV controller. Each position of the switch can be programmed to a different DVD player. Refer to your InteracTV User's Manual for instructions on how to use the 3-position memory switch.

InteracTV™ is a mark of Beep Telecommunications and Computing, L.L.C. Used under license.

Signs that you may need a macro -

1. When testing with the test card, the consumer is getting no functionality with the any buttons. A character macro maybe needed.
2. The controller is shipped with several default macros.  Certain DVD players require an enter command be sent after the numeric commands (arrow keys do not require enter), others require that all commands be sent multiple times (repeated). 
3. The macros are programmed after the manufacture code has been programmed.
4. There are two sets of macros.  One set controls the number of times a command is sent. 
5. The other sends additional characters with the number commands.

Additional characters:

• 0001 – Will send only the numeric command (1-9)
• 0002 – Will send the numeric command (1-9), then enter (default)
• 0003 – Will send zero then the numeric command (1-9)
• 0004 – Will send zero then the numeric command (1-9) then enter.

Number of times command is sent

• 0005 – Will send the IR command one time
• 0006 – Will send the IR command 2 times (default)
• 0007 – Will send the IR command 3 times

1. If no macro is entered the controller will use the default macros. In most cases the default macro will function fine and does not need to be changed.
2. The additional character macro is specific to the 3 pos. memory switch.  Every time a new manufacture code is programmed the Additional character macro will reset to the default code. 
3. The additional character macro only affects the number 1-9 it does not affect the arrow buttons
4. The number of times command is sent macro is assigned to all positions of the memory switch and will not reset to default even if a new manufacturers code is entered.  The consumer must reprogram it to change it.
5. When programming a macro each button pressed will flash the green indicator light once.  When the final digit is pressed and the macro is programmed the green indicator light will flash twice (just like when inserting a card).
6. After any of these commands are entered into the controller, the controller will stop responding to button presses until the card is removed and re-inserted.
7. Version 1.0 remotes do not support macros and will not display the double blink after the 4th button is pressed.