You can, but the adhesive should be applied to a clean, smooth, dry surface when the temperature is above 50°F (10°C). If the temperature is below 50°F, you can heat the surface with a hair dryer before application.

• Yes, for best results, allow the wax to cool for a few minutes before opening the mold. Twist the mold slightly (as you would an ice cube tray) to break the wax free. You can also run the mold under cold water, which will help speed up the cooling process. If the car body is wet, be sure to dry it completely before applying labels. Remove car body from the mold within 10 minutes. If the body is left in the mold for any longer, the wax may begin to crack.

You can combine your pens to get more color combinations. For example, you can get green by applying blue and yellow inks over each other. First apply a thin layer of one color until you get the desired coverage, then switch pens and apply an even layer of your second ink. Try making your own combinations!

You need to fine tune the spray nozzle by turning the adjustment nozzle all the way to the negative side (-). Then while holding the trigger down, slowly adjust the nozzle toward the positive side (+) until you get a nice even spray. You should also make sure that the pen is fully inserted by pushing it all the way into the slot on the spray gun until you hear/feel it click.

Make sure the pen is fully inserted by pushing it all the way into the slot on the spray gun until you hear/feel it click. Start spraying with the nozzle adjuster pointed all the way toward the negative side (-) and, while holding the trigger down, slowly move the adjuster toward the positive side (+) until you get a nice even spray. If you’re still having issues, please refer to the troubleshooting section below.

You need to fine tune the spray nozzle by turning the adjustment nozzle all the way to the negative side (-). Then while holding the trigger down, slowly adjust the nozzle toward the positive side (+) until you get a nice even spray. You should also make sure that the pen is fully inserted by pushing it all the way into the slot on the spray gun until you hear/feel it click.

• The very first time you use Car Maker, you need to insert 2 wax sticks. Car Maker comes pre-loaded with 1 wax stick. The second stick you insert is not meant to fit completely inside the machine – it will protrude through the top. After you have made your very first car, only 1 additional wax stick needs to be inserted every time. Please note that ALL wax sticks must be inserted with the point side down.

To clean the ink off of your car, rub it with a damp cloth and start again!

• DO NOT start injecting wax until Car Maker prompts you to “Please pull down handle.” If you start the injection before this, it can cause blockage in the mold. Blockage can be cleared using the included tool (see CLEANING section in the instruction sheet).

On the underside of the launcher, each end of the rubber band should be wrapped around a peg on each side of the main launcher and then doubled up and hooked around the center tab of the moveable portion of the launcher.

Here is a picture of an assembled rubber band launcher!

To cover existing paint or color you will need to apply multiple coats. First paint a thin, light coat and let it dry. Then repeat the process until you get the paint coverage you want.

The booster needs to be correctly assembled to its designated wall bracket in order to function.   The designated wall bracket has a notch on it.  This notch ensures the motor only works when attached to the bracket.  All other brackets are flat. 

Watch set-up instructions for your track.

• Once Car Maker instructs you to pull the handle, you must immediately pull it all the way down in one continuous motion until you hear “Complete.” For best results, DO NOT pump handle when pulling it down and complete the injection within 2-3 seconds. If you do not pull it all the way down to complete the injection, Car Maker will keep repeating the phrase, “Please pull down handle.”

• You need to hold the door closed and press the button above it to lock the door. Do not try to open the door during the heating or cooling cycle when it is locked.

• If you have inserted different colored wax sticks next to each other, you may get some color blending (in which the wax from the two adjacent sticks mix when creating the car body).

You should hear/feel it click when you push the pen down into its slot on the spray gun.

• If your car body came out only partially completed, see instructional video or try the following:
• Ensure you are inserting enough wax sticks into the machine and they are positioned next to each other in the proper alignment (point side down).  Remember, it’s normal for one of the wax sticks to protrude from the top.
• Ensure the handle is pulled all the way down in one continuous motion and the injection is completed within 2-3 seconds until you hear “Complete.”

• Ensure the mold has been thoroughly cleaned before starting your cycle.

Push the handle on the far right counterclockwise all the way to the ground and the car platform will tip forward, allowing your car to roll out.

Instructional videos include a review of box contents, items you'll need to get started and helpful tips about Hot Wheels Wall Tracks.