|
|
Always remove the marker from the Monster Maker when printing is complete. Replace cap on marker immediately after use. Store the markers in the tool stand, cap side down, when not in use. If left uncapped, markers will dry out. Markers can be partially restored by replacing the caps and storing them in the tool stand, cap side down, for 24 hours. Use the included markers only with the Monster Maker.
|
In the drawer, on the right side of the printer.
|
-
Monster Maker is made for iPad Air, iPad mini with Retina display, iPad (4th generation), iPad mini, and iPad (3rd generation). iOS 7.0 or higher is required.
-
Monster Maker is compatible with Samsung Galaxy Tab®, Samsung Galaxy Tab® 2, Samsung Galaxy Tab® 3, Samsung Galaxy Tab®, 8.9, Samsung Galaxy Tab® 10.1, Samsung Galaxy Note®, Google Nexus 7 (2012), Google Nexus 7 (2013), Google Nexus 10, Sony Xperia™ Tablet Z, Toshiba Excite™.
|
|
Additional red, purple, and black markers are available in the Monster Maker Primary Extension Pack, sold separately.
|
|
Next to the On/Off switch, behind the rubber plug.
|
-
PC: Windows Vista, Windows 7, Windows 8, Windows 8.1, Intel® Core™ i3 Processor, 2 GB RAM
|
|
|
The app may display this message if the doll part is not installed completely. Make sure that the doll part is installed per the instructions, and that the carriage slide is lined up with the doll part icon.
|
For best results, make sure doll parts are clean and dry before installing in Monster Maker. If your design did not print completely, erase ink using the provided sponge. Add water and a little dish soap (not included) and rub with the sponge until the ink is removed. Dry the doll part thoroughly before putting it back in the Monster Maker.
|
Please go to
service.mattel.com
to request replacement parts . Please store the adapters in the tool stand when not in use.
|
|
|
No, Windows and Mac computers are supported only through USB. Please connect Monster Maker to your computer with a standard A-to-B USB printer cable (not included).
|
|
If you receive an error message during printing, turn off the Monster Maker using the power switch. Wait a few seconds and turn it back on. Restart the app.
|
· The action button is the button on the top of the figure’s base that you can press down in order to advance dialogue, use your character’s special ability in the game, and interact with your environment.
|
-
Once Car Maker instructs you to pull the handle, you must immediately pull it all the way down in one continuous motion until you hear “Complete.” For best results, DO NOT pump handle when pulling it down and complete the injection within 2-3 seconds. If you do not pull it all the way down to complete the injection, Car Maker will keep repeating the phrase, “Please pull down handle.”
|
The Hot Wheels Car Maker Troubleshooting Guide will help with any questions that arise during the car making process.
|
You can, but you will only be able to play the initial portion of each character’s game unless you have Apptivity toy for that character.
To play without the toy, use two fingers to move around the screen, and a third finger to press the action button.
|
-
If you cannot press the handle down, have an adult unplug the machine, wait ten seconds and then plug it back in to reset. Car Maker will automatically go into the cooling cycle. Do not unplug during this time. After you hear “Cooling Complete” and the door opens, try the following:
-
Check the mold for blockage. See CLEANING section in the instruction sheet.
-
Look into the front window on the machine. Ensure that there is a wax stick in the heating chamber and that the wax stick above it is properly aligned.
|
When playing the game, lift your figure or fingers off the screen for at least 4 seconds, and the pause menu will appear.
The checklist icon is the green notepaper at the left side of the screen. Tap it to access the checklist.
The checklist will indicate your next task or assignment within the game.
|
