|
The WWE Power Slammers Ring is supposed to get scuffed up after the figures wrestle, on purpose, to show “battle damage”.
|
After the figures are connected, cranked up and the head is pushed, the “wrestling” feature does not last long.
- Crank the lever clockwise until it clicks, usually about 11 times, for full power battling.
|
When the WWE Power Slammers figures are connected, cranked up and the head is pushed to start, they start to move, but then get caught or don’t move.
-
For the Thunder Twisting figures, John Cena, Zack Ryder and Sheamus, make sure the arm is straight before you push the head to start the wrestling. If the arm is bent it causes the figures to get caught and not wrestle.
|
The WWE Power Slammers figures are difficult to connect at the arms the first couple of times. Each time you connect the figures, it will become easier and easier to connect.
The new figures released in the Fall 2013 will be easier to connect.
|
We have a network of over 350 Authorized Service Centers to help you with repairs and replacement parts. These Service Centers have skilled personnel and use only genuine Power Wheels replacement parts to fix your vehicle. Use our Service Center Locator to find a service center near you.
|
We have a network of over 350 Authorized Service Centers to help you with repairs and replacement parts. These Service Centers have skilled personnel and use only genuine Power Wheels replacement parts to fix your vehicle. Use our Service Center Locator to find a service center near you.
|
For any issue with the Power Wheels® 12V Quick Charger please follow this Flow Chart.
|
Make sure you charge the battery for at least 18 hours (30 hours max) before operating your vehicle for the first time. Charge the battery for at least 14 hours after each use of the vehicle. *It is necessary to charge the battery immediately after use. It is damaging to the battery when it has been used and then sits without being charged. After a full charge the battery can sit up to two-three months when not in use.
|
In order for the Wild Thing™ to operate correctly, there must be weight in the seat. When your child leans forward in the seat or lifts their bottom off the seat, the seat switch will open and the vehicle will stop. For best results, make sure your little one stays seated at all times with their back against the seat.
|
- Change batteries
- Check for obstructions around moving parts
|
The Power Wheels® 12V Quick Charger will not produce an output until it is plugged into a working Power Wheels® battery. The charger needs to detect a battery before it starts charging, so no voltage will be present when testing it with a volt meter.
|
Traction bands have been designed for and are included for use on specific single seat Jeep models to improve traction. The unauthorized use of traction bands on other Power Wheels® vehicles will void the product warranty and may pose both safety and reliability issues including decreased motor and/or gearbox life.
|
Due to the technical nature of Power Wheels® products, some Power Wheels® parts may only be installed by our authorized service centers, therefore we’re unable to provide repair manuals or diagrams. Power Wheels® has independently owned and operated authorized service centers that carry replacement parts, batteries, and chargers in addition to repairing vehicles in or out of warranty. Our Service Center locator will assist you in finding one of our authorized service centers in your area as well as provide you website addresses for service centers that offer on-line shopping.
|
|
Do not place used batteries in your regular trash. Instead, return the battery to a federal or state approved lead-acid battery recycler. This may be a Power Wheels® Authorized Service Center or a local retailer of automotive batteries.
|
Battery life will vary depending on how you follow the Charging and Battery Care Instructions. It's also affected by the total number of hours the batteries are used. Average battery life is one to three years.
|
If all codes in the instruction manual have been tried unsuccessfully or your brand of DVD player is not listed, it is possible that the code for your DVD player may still be in the controller. You may be able to find the code using the manual search method.
- Make sure the controller has good batteries and slide the 3 position memory switch on the back of the controller to the desired memory position.
- Insert the compilation DVD into the DVD player and turn on the DVD player and TV.
- Insert the programming card into the controller, the green light should blink twice.
- Point the controller at the DVD player and press the left arrow key.
- Continue to press the left arrow key at a 1 second interval. Be sure to watch to see if the power to the DVD player turns off.
- If the power to the DVD player turns off stop and remove the programming card. Turn the DVD player back on. Play the disk and allow the DVD footage to play through until it gets to the screen, which shows the 5 different activity cards.
- Insert the test card into the controller, the green light should blink twice.
- The DVD should skip to the test screen, if it does not remove the test card and re-insert the programming card and continue from step 5.
This process may take a while. If you press the left arrow button more than 300 times and the green light no longer blinks, it is possible that your DVD player's code is not supported by this version of the controller. Verify version and if new version includes more codes for their DVD player. If so, send a new controller. If no new codes have been added to their brand of DVD player, you will need to follow the service policy, return for voucher or refund.
If the test card skips to the footage, which resembles the test card then proceed with testing the controller. See Testing the unit section of your manual or quick set up instructions.
|
|
We recommend using alkaline batteries with our products, as they are great for long-term use and help optimize performance. We don't recommend using Carbon-Zinc batteries. While Carbon-Zinc batteries may work well with low-power devices, they can drain after a short period of time and cause certain products to not function properly.
|
|
https://qservice.corp.mattel.com/us/Docs/>A. We recommend using alkaline batteries with our products, as they are great for long-term use and help optimize performance. We don't recommend using Carbon-Zinc batteries. While Carbon-Zinc batteries may work well with low-power devices, they can drain after a short period of time and cause certain products to not function properly.
|
|
https://qservice.corp.mattel.com/us/Docs/>A. We recommend using alkaline batteries with our products, as they are great for long-term use and help optimize performance. We don't recommend using Carbon-Zinc batteries. While Carbon-Zinc batteries may work well with low-power devices, they can drain after a short period of time and cause certain products to not function properly.
|
The Camera/Printer has failed error appears when there is a communication error between the printer and the computer. To correct this issue:
- Close the software
- Unplug and re-plug in the power cord and USB
- Wait for the printer to turn on
- Restart the software
|
