For any issue with the Power Wheels® 12V Quick Charger please follow this Flow Chart.
|
Traction bands have been designed for and are included for use on specific single seat Jeep models to improve traction. The unauthorized use of traction bands on other Power Wheels® vehicles will void the product warranty and may pose both safety and reliability issues including decreased motor and/or gearbox life.
|
We have a network of over 350 Authorized Service Centers to help you with repairs and replacement parts. These Service Centers have skilled personnel and use only genuine Power Wheels replacement parts to fix your vehicle. Use our Service Center Locator to find a service center near you.
|
The Power Wheels® 12V Quick Charger will not produce an output until it is plugged into a working Power Wheels® battery. The charger needs to detect a battery before it starts charging, so no voltage will be present when testing it with a volt meter.
|
Due to the technical nature of Power Wheels® products, some Power Wheels® parts may only be installed by our authorized service centers, therefore we’re unable to provide repair manuals or diagrams. Power Wheels® has independently owned and operated authorized service centers that carry replacement parts, batteries, and chargers in addition to repairing vehicles in or out of warranty. Our Service Center locator will assist you in finding one of our authorized service centers in your area as well as provide you website addresses for service centers that offer on-line shopping.
|
Battery life will vary depending on how you follow the Charging and Battery Care Instructions. It's also affected by the total number of hours the batteries are used. Average battery life is one to three years.
|
Make sure you charge the battery for at least 18 hours (30 hours max) before operating your vehicle for the first time. Charge the battery for at least 14 hours after each use of the vehicle. *It is necessary to charge the battery immediately after use. It is damaging to the battery when it has been used and then sits without being charged. After a full charge the battery can sit up to two-three months when not in use.
|
We have a network of over 350 Authorized Service Centers to help you with repairs and replacement parts. These Service Centers have skilled personnel and use only genuine Power Wheels replacement parts to fix your vehicle. Use our Service Center Locator to find a service center near you.
|
|
Do not place used batteries in your regular trash. Instead, return the battery to a federal or state approved lead-acid battery recycler. This may be a Power Wheels® Authorized Service Center or a local retailer of automotive batteries.
|
If your vehicle was originally equipped with a Green 6v 6amp Power Wheels® battery, a Connector Converter may be used to allow the use of a Red 6V 9.5 amp Power Wheels® battery.
Connector Converters should not be used on any product purchased before October of 1998.
If you have any questions or would like to obtain a Connector Converter, please have your product number with you and contact Consumer Relations at 1-800-432-5437.
|
|
Since 1968, when Hot Wheels cars were introduced, we have manufactured tracks in many different colors, yet the color that sticks in the minds of most people is orange. As in the past, we will continue to manufacture tracks in many different colors that will vary from set to set, and year to year.
|
Hot Wheels replacement parts are available at our
Parts Store.
|
-
Yes, for best results, allow the wax to cool for a few minutes before opening the mold. Twist the mold slightly (as you would an ice cube tray) to break the wax free. You can also run the mold under cold water, which will help speed up the cooling process. If the car body is wet, be sure to dry it completely before applying labels. Remove car body from the mold within 10 minutes. If the body is left in the mold for any longer, the wax may begin to crack.
|
Instructional videos include a review of box contents, items you'll need to get started and helpful tips about Hot Wheels Wall Tracks.
|
You should hear/feel it click when you push the pen down into its slot on the spray gun.
|
|
|
There is a silver-colored speed control button on the lower left side of the screen. The image on it is a gear box. Tap the button to move from “Stop” mode to “Slow” and “Fast” modes.
|
You need to fine tune the spray nozzle by turning the adjustment nozzle all the way to the negative side (-). Then while holding the trigger down, slowly adjust the nozzle toward the positive side (+) until you get a nice even spray. You should also make sure that the pen is fully inserted by pushing it all the way into the slot on the spray gun until you hear/feel it click.
|
-
If you cannot press the handle down, have an adult unplug the machine, wait ten seconds and then plug it back in to reset. Car Maker will automatically go into the cooling cycle. Do not unplug during this time. After you hear “Cooling Complete” and the door opens, try the following:
-
Check the mold for blockage. See CLEANING section in the instruction sheet.
-
Look into the front window on the machine. Ensure that there is a wax stick in the heating chamber and that the wax stick above it is properly aligned.
|
You can, but the adhesive should be applied to a clean, smooth, dry surface when the temperature is above 50°F (10°C). If the temperature is below 50°F, you can heat the surface with a hair dryer before application.
|
