The following car seats are compatible with the J6669/L5344 Stand 'n Ride Stroller:

• Graco SnugRide
• Graco Infant Safe Seat
• Britax Companion Infant Car Seat
• Fisher-Price Safe Voyage Infant Car Seat

You should place the Apptivity Hot Wheels car on the screen in that location in order to play.

Please note that this product needs two sets of batteries, and there are two separate battery boxes. One battery box operates the swing feature and needs 4 “C” batteries.  The other battery box operates the vibration feature and requires 1 “D” battery.

If you've already changed the batteries and the swing is still not working, please contact one of our Fisher-Price® baby gear representatives by email or phone at 1-800-432-5437.

• You need to hold the door closed and press the button above it to lock the door. Do not try to open the door during the heating or cooling cycle when it is locked.

You should pull the car back so that your car stays in that location on the screen.

• If you hear “Error,” ask an adult to unplug Car Maker from the wall, wait ten seconds and then plug it back in to reset. Car Maker may automatically go into the cooling cycle. Do not unplug during this time. If you continue to hear “Error” after multiple resets, this may be an indication of a mechanical problem with the door switch; please contact Consumer Services via service.mattel.com for assistance.

The action button is the button on the hood of the car that you can press down in order to start the game, activate weapons, enter buildings and other zones, and more.

You can use your bouncer from birth until your child is able to sit up unassisted. The maximum weight limit is 25 pounds.

After you’ve airbrushed your car, lower the turntable into the drying chamber by turning the handle on the far right counterclockwise toward the ground. Rotate the knob outside the chamber all the way to the rightmost setting to turn the fan on. Air will blow inside the drying chamber and dry off your car!

• Once Car Maker instructs you to pull the handle, you must immediately pull it all the way down in one continuous motion until you hear “Complete.” For best results, DO NOT pump handle when pulling it down and complete the injection within 2-3 seconds. If you do not pull it all the way down to complete the injection, Car Maker will keep repeating the phrase, “Please pull down handle.”

• The very first time you use Car Maker, you need to insert 2 wax sticks. Car Maker comes pre-loaded with 1 wax stick. The second stick you insert is not meant to fit completely inside the machine – it will protrude through the top. After you have made your very first car, only 1 additional wax stick needs to be inserted every time. Please note that ALL wax sticks must be inserted with the point side down.

• Yes, for best results, allow the wax to cool for a few minutes before opening the mold. Twist the mold slightly (as you would an ice cube tray) to break the wax free. You can also run the mold under cold water, which will help speed up the cooling process. If the car body is wet, be sure to dry it completely before applying labels. Remove car body from the mold within 10 minutes. If the body is left in the mold for any longer, the wax may begin to crack.

• If you cannot insert or remove the mold, locate the tabs on both sides of Car Maker (underneath handle), push them up and try again.

A: Your baby’s safety has always been our top priority. The seat is designed to hug and support your baby as they sit up and discover the world around them. When your baby is ready to be back in your loving arms, gently pull him or her out of the seat from the back, placing one foot on the base for stability.

You may use your Booster Seat with a child who has enough upper body control to sit up unassisted; 45 pounds maximum.

Use the restraint system until your child is able to get in and out of the product unassisted (about 2 ½ years old). 

• In order to create a solid one-colored car body, you must insert multiple wax sticks of the same color next to each other.

There is a silver-colored speed control button on the lower left side of the screen. The image on it is a gear box.  Tap the button to move from “Stop” mode to “Slow” and “Fast” modes.

Push the handle on the far right counterclockwise all the way to the ground and the car platform will tip forward, allowing your car to roll out.