The following car seats are compatible with the J6669/L5344 Stand 'n Ride Stroller:

• Graco SnugRide
• Graco Infant Safe Seat
• Britax Companion Infant Car Seat
• Fisher-Price Safe Voyage Infant Car Seat

To clean the ink off of your car, rub it with a damp cloth and start again!

• Once Car Maker instructs you to pull the handle, you must immediately pull it all the way down in one continuous motion until you hear “Complete.” For best results, DO NOT pump handle when pulling it down and complete the injection within 2-3 seconds. If you do not pull it all the way down to complete the injection, Car Maker will keep repeating the phrase, “Please pull down handle.”

• If you cannot press the handle down, have an adult unplug the machine, wait ten seconds and then plug it back in to reset. Car Maker will automatically go into the cooling cycle. Do not unplug during this time. After you hear “Cooling Complete” and the door opens, try the following:
• Check the mold for blockage. See CLEANING section in the instruction sheet.
• Look into the front window on the machine. Ensure that there is a wax stick in the heating chamber and that the wax stick above it is properly aligned.

You should place the Apptivity Hot Wheels car on the screen in that location in order to play.

• The very first time you use Car Maker, you need to insert 2 wax sticks. Car Maker comes pre-loaded with 1 wax stick. The second stick you insert is not meant to fit completely inside the machine – it will protrude through the top. After you have made your very first car, only 1 additional wax stick needs to be inserted every time. Please note that ALL wax sticks must be inserted with the point side down.

Please note that this product needs two sets of batteries, and there are two separate battery boxes. One battery box operates the swing feature and needs 4 “C” batteries.  The other battery box operates the vibration feature and requires 1 “D” battery.

If you've already changed the batteries and the swing is still not working, please contact one of our Fisher-Price® baby gear representatives by email or phone at 1-800-432-5437.

• You need to hold the door closed and press the button above it to lock the door. Do not try to open the door during the heating or cooling cycle when it is locked.

• Yes, for best results, allow the wax to cool for a few minutes before opening the mold. Twist the mold slightly (as you would an ice cube tray) to break the wax free. You can also run the mold under cold water, which will help speed up the cooling process. If the car body is wet, be sure to dry it completely before applying labels. Remove car body from the mold within 10 minutes. If the body is left in the mold for any longer, the wax may begin to crack.

You should pull the car back so that your car stays in that location on the screen.

• If your car body came out only partially completed, see instructional video or try the following:
• Ensure you are inserting enough wax sticks into the machine and they are positioned next to each other in the proper alignment (point side down).  Remember, it’s normal for one of the wax sticks to protrude from the top.
• Ensure the handle is pulled all the way down in one continuous motion and the injection is completed within 2-3 seconds until you hear “Complete.”

• Ensure the mold has been thoroughly cleaned before starting your cycle.

• If you cannot insert or remove the mold, locate the tabs on both sides of Car Maker (underneath handle), push them up and try again.

A: Your baby’s safety has always been our top priority. The seat is designed to hug and support your baby as they sit up and discover the world around them. When your baby is ready to be back in your loving arms, gently pull him or her out of the seat from the back, placing one foot on the base for stability.

• DO NOT start injecting wax until Car Maker prompts you to “Please pull down handle.” If you start the injection before this, it can cause blockage in the mold. Blockage can be cleared using the included tool (see CLEANING section in the instruction sheet).

In swing mode, you can use your Take-Along Swing until your child becomes active and can climb out of the swing. The maximum weight limit is 25 pounds.

In infant seat mode, you may use your Take-Along Seat until your child is able to sit up unassisted. In this case, 25 pounds is also the maximum weight limit.

You may use your Booster Seat with a child who has enough upper body control to sit up unassisted; 45 pounds maximum.

Use the restraint system until your child is able to get in and out of the product unassisted (about 2 ½ years old). 

• If you hear “Error,” ask an adult to unplug Car Maker from the wall, wait ten seconds and then plug it back in to reset. Car Maker may automatically go into the cooling cycle. Do not unplug during this time. If you continue to hear “Error” after multiple resets, this may be an indication of a mechanical problem with the door switch; please contact Consumer Services via service.mattel.com for assistance.