You only need to set up your InteracTV controller one time per DVD player. Your InteracTV controller can be set up to be played with up to three different DVD players. There is a 3-position memory switch on the underside of your InteracTV controller. Each position of the switch can be programmed to a different DVD player. Refer to your InteracTV User's Manual for instructions on how to use the 3-position memory switch.
InteracTV™ is a mark of Beep Telecommunications and Computing, L.L.C. Used under license.
|
Try each of the codes listed under "ALL MODELS" for your DVD player's manufacturer until you find one that can work properly for all shapes on the test screen and both the skip ahead and skip back on the Read With Me™ controller.
|
|
Consult with your Read With Me instruction manual. You will need to program your Read With Me controller using method 2 - using manufacture codes, or method 3 - manual search.
|
If your DVD player is not responding to your Read With Me™ controller please try the following:
- Make sure you have setup Read With Me™ controller correctly. The quick setup sheet can be found at www.service.fisher-price.com and the latest list of codes can be found at www.service.fisher-price.com
- Try moving your Read With Me™ controller closer to the TV.
- Replace the batteries on your Read With Me™ controller.
- Make sure your Read With Me™ controller is pointed directly at your DVD player.
- Always be sure your hand and the activity card are not covering the red window on the front of the Read With Me™ controller when pressing a button to respond to an activity.
- Make sure there are no large objects between your Read With Me™ controller and your DVD player. Large objects can block the signal between your controller and DVD player.
- Double check that the 3-position memory switch on the underside of your Read With Me™ controller is in the proper position. Refer to your Read With Me™ User’s Manual for instructions on how to use the 3-position memory switch.
|
|
Try each of the codes listed under "ALL MODELS" for your DVD player's manufacturer until you find one that can work properly for all shapes on the test screen and both the skip ahead and skip back on the Read With Me™ controller.
|
|
The cards were switched while the unit was pointed away from the DVD player. Simply pull the card out and reinsert it while pointing the controller at the DVD player.
|
Each DVD player will respond differently to your InteracTV controller. Some players will take longer to access the DVD then other players do. For the best results, please make sure that you press the button one time and then wait a few seconds for a reaction from your DVD player. If you do not get a reaction from your DVD player after a few seconds, try pressing the button again. Also, make sure you are pressing the buttons firmly.
InteracTV™ is a mark of Beep Telecommunications and Computing, L.L.C. Used under license.
|
If your DVD player is not responding to your InteracTV controller please try the following:
- Make sure you have set up your InteracTV controller correctly.
- Try moving your InteracTV controller closer to the TV.
- Replace the batteries on your InteracTV controller.
- Make sure your InteracTV controller is pointed directly at your DVD player.
- Always be sure your hand and the activity card are not covering the red window on the front of the InteracTV controller when removing and inserting an activity card.
- Make sure there are no large objects between your InteracTV controller and your DVD player. Large objects can block the signal between your controller and DVD player.
- When changing activity cards, always make sure you remove the activity card from your InteracTV controller slowly, wait a few seconds, and then insert another activity card.
- Double check that the 3-position memory switch on the underside of your InteracTV controller is in the proper position. Refer to your InteracTV User's Manual for instructions on how touse the 3-position memory switch.
InteracTV™ is a mark of Beep Telecommunications and Computing, L.L.C. Used under license.
|
An acceptable code was entered, however, it is not functional with your DVD player or, the back button was pressed too many times. You will have to restart the programming process.
|
|
Yes. You can pause Read With Me™ at any time using the pause button on the Read With Me™ controller or the remote control that came with your DVD player.
|
|
The InteracTV can be programmed to operate up to 3 different DVD players.
|
|
You only need to setup your Read With Me™ controller one time per DVD player. Your Read With Me™ controller can setup to be played with up to 3 different DVD players. There is a 3-position memory switch on the underside of your Read With Me™ controller. Each position of the switch can be programmed to a different DVD player. Refer to your Read With Me™ User’s Manual for instructions on how to use the 3-position memory switch.
|
|
It controls the DVD player using infrared commands, just like any universal remote.
|
If all codes in the instruction manual have been tried unsuccessfully or your brand of DVD player is not listed, it is possible that the code for your DVD player may still be in the controller. You may be able to find the code using the manual search method.
- Make sure the controller has good batteries and slide the 3 position memory switch on the back of the controller to the desired memory position.
- Insert the compilation DVD into the DVD player and turn on the DVD player and TV.
- Insert the programming card into the controller, the green light should blink twice.
- Point the controller at the DVD player and press the left arrow key.
- Continue to press the left arrow key at a 1 second interval. Be sure to watch to see if the power to the DVD player turns off.
- If the power to the DVD player turns off stop and remove the programming card. Turn the DVD player back on. Play the disk and allow the DVD footage to play through until it gets to the screen, which shows the 5 different activity cards.
- Insert the test card into the controller, the green light should blink twice.
- The DVD should skip to the test screen, if it does not remove the test card and re-insert the programming card and continue from step 5.
This process may take a while. If you press the left arrow button more than 300 times and the green light no longer blinks, it is possible that your DVD player's code is not supported by this version of the controller. Verify version and if new version includes more codes for their DVD player. If so, send a new controller. If no new codes have been added to their brand of DVD player, you will need to follow the service policy, return for voucher or refund.
If the test card skips to the footage, which resembles the test card then proceed with testing the controller. See Testing the unit section of your manual or quick set up instructions.
|
The following steps will allow you to program your InteracTV controller:
- Make sure the InteracTV controller has good batteries. Slide the 3 position memory switch, on the back of the controller, to the desired memory position. The controller is capable of being setup for up to 3 different DVD players in 3 different locations.The controller must be setup and tested individually for each of the 3 DVD players, but once that is done the controller will retain the manufacturer's code and does not need to be setup again.If the consumer accidentally enters a new valid 4-digit manufacturer’s code, then they must set it up again for that DVD player.It is a good idea to write the 4-digit manufacturer’s code in the labeling area provided on the back of the controller.
- Insert the compilation DVD into the DVD player and turn on the DVD player and TV.
- Insert the programming card into the controller; the green light should blink twice.
- Locate the manufacturer’s codes in the user’s manual.
- Enter the first 4 digit code listed under the manufacturer. Use the right arrow button for the number. The light should blink after each button press and blink a long blink after the 4th digit is entered.
- Remove the programming card.The light should double blink when the card is removed
- Insert the test card into the unit;the green light should double blink.
- The DVD should skip to the test screen, if it does not, repeat from step 3, choosing the next manufacturer’s code on the list. If the test card skips to the footage, which resembles the test card, then proceed with testing the unit.See Testing the unit section of you manual or quick setup instructions.
- If you have tried all of the manufacturer's codes listed and you cannot locate an acceptable code, see programming the unit using manual search in your user's manual.
|
Here are some tips that may help you during the quick setup:
- Make sure you are using fresh alkaline batteries inside your InteracTV controller.
- If you have followed the instructions on the quick setup sheet and your InteracTV controller is still not working with your DVD player, try the setup sheet again from the beginning. It is possible that one of the numbers did not register when you entered in your DVD code.
- When pressing the numbers on the programming card, make sure your press each number firmly and slowly. The green light on your controller should blink one time after each number is pressed. When the fourth digit is pressed, make sure the green light on your InteracTV controller blinks one long blink. If you do NOT see this long blink, remove the programming card, re-insert it into the controller and try the same code again.
InteracTV™ is a mark of Beep Telecommunications and Computing, L.L.C. Used under license.
|
No. The setup of your controller is required only one time for each DVD player with which you are using your InteracTV controller. If you have correctly setup your controller with the software that was included with your InteracTV controller, the controller should work with the separately sold software titles.
InteracTV™ is a mark of Beep Telecommunications and computing, L.L.C. Used under license.
|
If you are stuck in an activity after repeated attempts to remove and insert an activity card, please place the activity card back into the InteracTV controller and wait for the next activity to appear on the screen. When the next activity appears on the screen, remove the card from your InteracTV controller. The menu screen should now appear on the screen. If the menu screen does not appear on your screen you need to restart the InteracTV DVD. Press stop on your DVD player and then press play to restart the DVD.
InteracTV™ is a mark of Beep Telecommunications and Computing, L.L.C. Used under license.
|
You must restart the programming process. Follow the steps below to begin:
- Shut off your DVD player.
- Remove the cover from the controller to begin audio prompts.
- Begin programming.
- Once programming procedure has been completed, move forward to retest the controller.
|
Please restart the Smart Remote programming process, and retest the controller. If this method is unsuccessful, please check the latest DVD code list to find the proper code for your DVD player. The latest code listing can be found at www.service.fisher-price.com. Also, if you do not have your quick setup sheet, you can download it at www.service.fisher-price.com. Please try setting up your Read With Me™ again using this Smart Remote method and quick setup sheet.
Here are some tips that may help you during the quick setup: Make sure you are using fresh alkaline batteries inside your Read With Me™ controller.
-
If you have followed the instructions on the quick setup sheet and your Read With Me ™ controller is still not working with your DVD player, try the setup again from the beginning.
-
It is possible that one of the signals did not register when pressed on your DVD player’s remote.
-
When pressing the numbers on your DVD remote be sure to wait for the audio prompt to finish and the LED on the Read With Me™ controller turns on.
|
